Saturday, March 3, 2012

Jacques Cartier Bridge Gets New Shocks

Here’s your chance to see the underbelly of the Jacques Cartier Bridge.

Last week, you may have heard that the Jacques Cartier was being closed overnight and seen the scaffolding around piers that hold up a bridge ramp at the northwest corner of Ste. Catherine St. and De Lorimier Ave.

Workers removed the 82-year-old hunk of steel (in the photo above) that helps hold up a 336-tonne section of the bridge. They were making way for a new shock absorber for the span.

Workers were replacing a part of the structure known as a bearing device. It sits at the top of a pier and transfers the load from the deck to the piers.

In this case, the bearing device is of a type that allows for slight movements in the bridge’s superstructure. It acts as a sort of shock absorber for the bridge, absorbing movements due to traffic and changes in temperature, says Jean-Vincent Lacroix of the Jacques Cartier and Champlain Bridges Inc.

The devices being replaced were installed more than 20 years ago. They are rusty and inspections indicate they should be replaced, Lacroix said. These are not emergency repairs, he added. They’re part of regular maintenance.

I went up to watch some of the work on Feb. 23.

The federal bridge agency is replacing bearing devices on 12 sections of the bridgebetween February and June this year. It’s part of a five-month, $3.5-million renovation that will require the bridge to be completely closed for about 15 brief overnight periods over the next four months.

Here’s how you change a bearing device:

1) Install scaffolding under and around two piers (one on either side of the bridge) where the bearing devices will be replaced.

photo 31 10 steps: How to change the Jacques Cartier Bridges shock absorbers

jacques cartier bridge 0011 e1330456709976 10 steps: How to change the Jacques Cartier Bridges shock absorbers

jacques cartier bridge 0431 e1330456951577 10 steps: How to change the Jacques Cartier Bridges shock absorbers
.

.

2) Install support beams next to and attached to the piers in question.

jacques cartier bridge 0381 e1330457052971 10 steps: How to change the Jacques Cartier Bridges shock absorbers
.

.

3) Close the bridge to traffic between 1 a.m. and 4 a.m. Use a powerful hydraulic jack to lift a 336-tonne section of the bridge slightly (up to 10 millimetres).

orange cones 10 steps: How to change the Jacques Cartier Bridges shock absorbers

.

.

4) Reopen bridge to traffic. Motorists won’t notice the fact that part of the bridge is slightly askew. 

jacques cartier googlemaps e1330703734225 10 steps: How to change the Jacques Cartier Bridges shock absorbers

.

.

5) Cut out and remove the top of the pier. In this case, most of the section removed dates from the bridge’s opening in 1930 (the green part in the photo below), but the rusty bearing device on top of it had been replaced in 1980. All that rust made it less effective.

jacques cartier bridge 0031 e1330457214673 10 steps: How to change the Jacques Cartier Bridges shock absorbers

jacques cartier bridge 0061 e1330457246491 10 steps: How to change the Jacques Cartier Bridges shock absorbers

jacques cartier bridge 0401 e1330456822831 10 steps: How to change the Jacques Cartier Bridges shock absorbers

.

.

6) Install thick new steel plates and bolt them to the structure. The top of the pier has to be removed because of these new plates. The plates will make it easier to replace the bearing device when it’s time is up in about 25 years. Thanks to these plates, next time, they won’t have to install the support beams in Step 2.

jacques cartier bridge 0101 10 steps: How to change the Jacques Cartier Bridges shock absorbers

jacques cartier bridge 0121 e1330457348300 10 steps: How to change the Jacques Cartier Bridges shock absorbers

.

.

7) Install the new bearing device between the steel plates.

jacques cartier bridge 0311 e1330457378796 10 steps: How to change the Jacques Cartier Bridges shock absorbers

.

.

8)  Close the bridge to traffic again from 1 a.m. and 4 a.m. and lower the bridge deck back to its normal location.

photo 21 10 steps: How to change the Jacques Cartier Bridges shock absorbers

.

.

9) Reopen the bridge.

jacques cartier googlemaps e1330703734225 10 steps: How to change the Jacques Cartier Bridges shock absorbers

.

.

10) Return in about 2037 to replace the bearing device again.

   ..............................So there you have replacing a shock on the JC Bridge , Cheers ! HF&RV - Les

No comments: